5,366
edits
Changes
no edit summary
<onlyinclude>
This is for a DIY installation for the [[Charge Tank]]'s inlet bracket, useful for many aftermarket charging solutions.
;Parts
: Bracket p/n 12-08047XX (formerly p/n 12-0804713; might also be 26-08096) special order $106 USD
{|
| [[File:MY2016DSR_chargetankhwinletbracketkit_inventorylabel1216.jpg|thumb]]
| [[File:MY2016DSR_chargetankhwinletbracketkit_inventorylabelold.jpg|thumb]]
|-
| [[File:MY2016DSR_chargetankhwinletbracketkit_open1.jpg|thumb]]
| [[File:MY2016DSR_chargetankhwinletbracketkit_open2.jpg|thumb]]
| [[File:MY2016DSR_chargetankhwinletbracketkit_open3.jpg|thumb]]
|-
| [[File:MY2016DSR_chargetankhwinletbracketkit_contentsbags.jpg|thumb]]
| [[File:MY2016DSR_chargetankhwinletbracketkit_contentslayout1.jpg|thumb]]
| [[File:MY2016DSR_chargetankhwinletbracketkit_contentslayout2.jpg|thumb]]
|}
;Steps (Used MY2016 DSR)
#[[Common Modifications#Helmet Lock Removal|Remove helmet lock]]
# Thread the grounding strap onto the studded bracket and reinstall it through the frame.
#: '''Suggestion:''' Use a short section of painters masking tape stuck around the thread of the studs to itself like a "flag" to keep the ground strap secure in its position until the studded bracket can be fully seated to where the helmet lock used to be secured.
#: The "flag" can be pulled up through the bolt holes in the frame and removed when ready.
#: '''FIXME:''' There is an alternative way to secure the ground strap which is easier and recommended by the OEM.
#:[[File:MY2016DSR_chargetankbracket_groundstrapbracket.jpg|none|thumb]]
# ?? Take a guess. There's a bag of parts.
#: '''FIXME:''' Describe what all the parts are and how they should be installed.
#:[[File:MY2016DSR_chargetankbracket_scv2badinletdetail.jpg|none|thumb]][[File:MY2016DSR_chargetankbracket_scv2badinletview.jpg|none|thumb]]
# With the inlet bracket installed, two of the top mounting holes on the bracket are meant to be fastened through the chargetank cowl and into the inlet bracket.
#: You only need to mount the J1772 inlet itself to the bracket using the rear top two locations.
#: The front top two locations will be further secured when the chargetank cowl is mounted.
</onlyinclude>
[[Category:Install]]
This is for a DIY installation for the [[Charge Tank]]'s inlet bracket, useful for many aftermarket charging solutions.
;Parts
: Bracket p/n 12-08047XX (formerly p/n 12-0804713; might also be 26-08096) special order $106 USD
{|
| [[File:MY2016DSR_chargetankhwinletbracketkit_inventorylabel1216.jpg|thumb]]
| [[File:MY2016DSR_chargetankhwinletbracketkit_inventorylabelold.jpg|thumb]]
|-
| [[File:MY2016DSR_chargetankhwinletbracketkit_open1.jpg|thumb]]
| [[File:MY2016DSR_chargetankhwinletbracketkit_open2.jpg|thumb]]
| [[File:MY2016DSR_chargetankhwinletbracketkit_open3.jpg|thumb]]
|-
| [[File:MY2016DSR_chargetankhwinletbracketkit_contentsbags.jpg|thumb]]
| [[File:MY2016DSR_chargetankhwinletbracketkit_contentslayout1.jpg|thumb]]
| [[File:MY2016DSR_chargetankhwinletbracketkit_contentslayout2.jpg|thumb]]
|}
;Steps (Used MY2016 DSR)
#[[Common Modifications#Helmet Lock Removal|Remove helmet lock]]
# Thread the grounding strap onto the studded bracket and reinstall it through the frame.
#: '''Suggestion:''' Use a short section of painters masking tape stuck around the thread of the studs to itself like a "flag" to keep the ground strap secure in its position until the studded bracket can be fully seated to where the helmet lock used to be secured.
#: The "flag" can be pulled up through the bolt holes in the frame and removed when ready.
#: '''FIXME:''' There is an alternative way to secure the ground strap which is easier and recommended by the OEM.
#:[[File:MY2016DSR_chargetankbracket_groundstrapbracket.jpg|none|thumb]]
# ?? Take a guess. There's a bag of parts.
#: '''FIXME:''' Describe what all the parts are and how they should be installed.
#:[[File:MY2016DSR_chargetankbracket_scv2badinletdetail.jpg|none|thumb]][[File:MY2016DSR_chargetankbracket_scv2badinletview.jpg|none|thumb]]
# With the inlet bracket installed, two of the top mounting holes on the bracket are meant to be fastened through the chargetank cowl and into the inlet bracket.
#: You only need to mount the J1772 inlet itself to the bracket using the rear top two locations.
#: The front top two locations will be further secured when the chargetank cowl is mounted.
</onlyinclude>
[[Category:Install]]