Changes

Jump to: navigation, search

Kickstand Switch

3,720 bytes added, 02:50, 14 April 2020
added maintenance suggestion
<onlyinclude>
The [[Kickstand]] has a safety cutout switch (really a sensor) to prevent motor operation while at rest.

{{Kickstand Switch Hazard}}

;Part
: From observation, the [https://en.ad-asahidenso.co.jp/products/motorcycles/ Asahi Denso] CE122 proximity sensor appears to be the part match, also used on some Triumph and KTM motorcycle models.
: From the 2016 SR's sensor to its connector, the wires are Blue, Pinkish Red, and Black.
:: While the bike is keyed on and contactor is closed, Blue measures a stable 5V, Red measures ~2.7V and varies (need to scope this), and black appears to be a signal ground/input (needs verification when I'm not tired).
: Some KTM riders with the Asahi Denso CE122 sensor have reported success using commercial bypass kits.
:* [http://electricmotorcycleforum.com/boards/index.php?topic=9276.msg81168#msg81168 Reportedly], a [https://slavensracing.com/shop/sidestand-switch-bypass-removal-kit-ktm-690-950-990/ KTM sidestand switch bypass kit] can work on a Zero without issues.
:*: [https://www.youtube.com/watch?v=tglAUxsl51M Instructional video]
:*: {{#ev:youtube|tglAUxsl51M}}
:: One such user suggested these are merely a potted 2.2kOhm resistor between the Red and Black wires (link here).
:: Zero motorcycles can be far more sensitive to faults on signalling pins so this should not be attempted unless you absolutely know what you are doing, and are willing to risk having to replace your MBB.
: talonreaper has had luck on a 2016 SR with a 2.7kOhm resistor between the red and black kickstand sensor's wires to get home from being stranded in an emergency.
:: This is still not advised.
:: North or South pole magnetism activation? TODO

;Connector
: The connector appears to be a Sumimoto MT sealed series connector MT-3S-2, p/n 6180-3241.
: Ref. [https://www.corsa-technic.com/item.php?item_id=232&category_id=126&manufacturer_id=44 Corsa Technic reference page for 6180-3241]
: This connector appears to be a very standard application for Japanese motorcycle interlock sensors for sidestands/kickstands.

;Troubleshooting
: Raise the kickstand for testing only with the rear wheel lifted off the ground via a [[Lift|stand or lift]].
: The [[MBB Console#Status|status]] command in the MBB console can report its reading.

;Maintenance
: An unconfirmed suggestion per this [https://www.electricmotorcycleforum.com/boards/index.php?topic=9824 Side stand safety switch] discussion on EMF:
:: Since I was worried about the condition of my side stand safety switch and never having looked at it before, I got on my hands and knees under the bike and checked it out.
:: I noticed that there were a couple of wires that went into a plastic sheath that protects the wires and their connections within the switch housing from damage.
:: But I also noticed that the sheath's opening faces forward and it seemed like water and muck could be forced into the opening and perhaps short out the switch contacts under extreme conditions.
:: So what I did was to squirt some silicone sealant into the opening and sealed it off.
:: Hopefully, that will eliminate any possibility of water getting into the switch when riding on wet streets.

;Bypass
: ''If there is a compelling justification worth risking warranty damage'', the sensor interlock preventing operating the powertrain may be bypassed.
:: The bypass should be performed via [[MBB Console#Settings|MBB settings]] configuration.

{| class="wikitable"
|+ MBB pins (per 2013 trace)
!Pin #
!Wire Color
!Wire Gauge
|-
|10||Yellow/Black||20AWG
|-
|11||Orange/Black||20AWG
|-
|27||Red||20AWG
|}

;Removal
: See [[Kickstand Switch Removal]]

;Replacement
: See [[Kickstand Switch Replacement]]
</onlyinclude>

[[Category:Component]]

Navigation menu