5,366
edits
Changes
link update
<onlyinclude>
[[File:Board Mounting Plate - Front.png|thumb|Front]]
[[File:Board Mounting Plate - Rear.png|thumb|Rear]]
A vertical plate aft of the battery supports both the [[Gen2/Main Bike Board|Main Bike Board]] and the [[DC-DC 12V Converter]].
The plate varies between pre-2015 model years and the following model years, likely because of the DC converter upgrade in 2015 from 300W to 500W to support ABS braking equipment power requirements.
;Attachments
* The [[Gen2/Main Bike Board|Main Bike Board]] is mounted to the rear face of the plate for 2013-2014 models, and to the rear face of the upper edge of the plate on 2015+ models.
* The [[DC-DC 12V Converter]] is mounted to the forward face of the plate for 2013-2014 models, and to the lower rear face of the plate on 2015+ models.
* The [[Accessory Charging Port]] is screwed to a flange at the bottom of the plate via two small M2.5 allen key bolts.
* The rubber boot covering the Accessory Charging Port is attached to the flange via plastic push-rivet.
* One cable run is zip-tied to a slot in the lower left corner of the plate, accessible under the frame arms forward of the onboard charging plug.
* Another cable run is zip-tied a slot in the lower edge of the plate closer to the right side, accessible under the frame arms behind the battery.
;Mounting
* The bracket has side flanges that affix the plate to the left and right sides of the frame.
* The top two corners of the flanges bend to the rear of the bike at a 45 degree angle, which mate to similarly-positioned flanges on the frame sides. The frame side flanges are above the plate flanges, which means when installing and removing the plate, the top must be angled towards the rear of the bike.
* The bottom two corners of the flanges bend to the rear of the bike at a 90 degree angle. The bolts which affix these corners point upwards (cap head points down).
* Fasteners
** 4x M4 socket cap bolts, 12mm length, 0.75mm? depth, 5mm outer diameter, with washers.
** 2x M2.5 socket cap bolts, 25mm length with a 6mm shoulder, 0.5mm? depth, 2.5mm outer diameter, with washers.
** 2x M3 socket cap bolts, 10mm length, 0.75mm? depth, 4mm outer diameter, with washers.
;[[Board Mounting Plate Removal|Removal]]
{{:Board Mounting Plate Removal}}
</onlyinclude>
[[Category:Structural Component]]
[[File:Board Mounting Plate - Front.png|thumb|Front]]
[[File:Board Mounting Plate - Rear.png|thumb|Rear]]
A vertical plate aft of the battery supports both the [[Gen2/Main Bike Board|Main Bike Board]] and the [[DC-DC 12V Converter]].
The plate varies between pre-2015 model years and the following model years, likely because of the DC converter upgrade in 2015 from 300W to 500W to support ABS braking equipment power requirements.
;Attachments
* The [[Gen2/Main Bike Board|Main Bike Board]] is mounted to the rear face of the plate for 2013-2014 models, and to the rear face of the upper edge of the plate on 2015+ models.
* The [[DC-DC 12V Converter]] is mounted to the forward face of the plate for 2013-2014 models, and to the lower rear face of the plate on 2015+ models.
* The [[Accessory Charging Port]] is screwed to a flange at the bottom of the plate via two small M2.5 allen key bolts.
* The rubber boot covering the Accessory Charging Port is attached to the flange via plastic push-rivet.
* One cable run is zip-tied to a slot in the lower left corner of the plate, accessible under the frame arms forward of the onboard charging plug.
* Another cable run is zip-tied a slot in the lower edge of the plate closer to the right side, accessible under the frame arms behind the battery.
;Mounting
* The bracket has side flanges that affix the plate to the left and right sides of the frame.
* The top two corners of the flanges bend to the rear of the bike at a 45 degree angle, which mate to similarly-positioned flanges on the frame sides. The frame side flanges are above the plate flanges, which means when installing and removing the plate, the top must be angled towards the rear of the bike.
* The bottom two corners of the flanges bend to the rear of the bike at a 90 degree angle. The bolts which affix these corners point upwards (cap head points down).
* Fasteners
** 4x M4 socket cap bolts, 12mm length, 0.75mm? depth, 5mm outer diameter, with washers.
** 2x M2.5 socket cap bolts, 25mm length with a 6mm shoulder, 0.5mm? depth, 2.5mm outer diameter, with washers.
** 2x M3 socket cap bolts, 10mm length, 0.75mm? depth, 4mm outer diameter, with washers.
;[[Board Mounting Plate Removal|Removal]]
{{:Board Mounting Plate Removal}}
</onlyinclude>
[[Category:Structural Component]]
