5,366
edits
Changes
new category
<onlyinclude>
Tail wiring includes the [[#Tail_Light|tail lights]] (running and braking power), each rear [[#Turn_Signals|turn signal]], and the license plate illuminator.
{| class="wikitable"
|+ Connections
! Photo
! Connector
! Function
! Wire Color
|-
| rowspan="99"| [[File:ZeroTail17b.jpg|400px]]
| rowspan="3"| Standard Suzuki or Honda brake light (3-wire)
| Tail light power
| Brown
|-
| Brake light power
| White with red stripe
|-
| Negative/Return
| Black
|-
| rowspan="4"| Single pin connector
:Socket: [http://www.molex.com/molex/products/datasheet.jsp?part=active/0003092011_CRIMP_HOUSINGS.xml Molex 03-09-2011] [http://www.mouser.com/ProductDetail/Molex/03-09-2011/] [https://www.digikey.com/product-detail/en/molex-connector-corporation/03-09-2011/WM1303-ND/]
:Pin: [http://www.molex.com/molex/products/datasheet.jsp?part=active/0003091011_CRIMP_HOUSINGS.xml Molex 03-09-1011] [http://www.mouser.com/ProductDetail/Molex/03-09-1011/]
| Left turn signal power
| Green
|-
| Negative/Return
| Black
|-
| Right turn signal power
| Grey
|-
| Negative/Return
| Black
|}
;Note about Braking Regen
: Braking regen is activated by the pressure switch on the front brake lever or hydraulic switch on the rear brake pedal, through the rear brake power circuit.
: If that circuit doesn't complete (due to a failed bulb or wiring disconnect), braking regen seems to not activate.
;Routing
: Tail wiring runs through a sleeve by the [[#Controller|controller]] on the left side.
:: Ensure it is protected from chafing by the controller cover.
: Turn signal wires run through a pair of holes where the tail stalk meets the subassembly underneath the tail.
</onlyinclude>
[[Category:12V Component]]
[[Category:Wiring]]
Tail wiring includes the [[#Tail_Light|tail lights]] (running and braking power), each rear [[#Turn_Signals|turn signal]], and the license plate illuminator.
{| class="wikitable"
|+ Connections
! Photo
! Connector
! Function
! Wire Color
|-
| rowspan="99"| [[File:ZeroTail17b.jpg|400px]]
| rowspan="3"| Standard Suzuki or Honda brake light (3-wire)
| Tail light power
| Brown
|-
| Brake light power
| White with red stripe
|-
| Negative/Return
| Black
|-
| rowspan="4"| Single pin connector
:Socket: [http://www.molex.com/molex/products/datasheet.jsp?part=active/0003092011_CRIMP_HOUSINGS.xml Molex 03-09-2011] [http://www.mouser.com/ProductDetail/Molex/03-09-2011/] [https://www.digikey.com/product-detail/en/molex-connector-corporation/03-09-2011/WM1303-ND/]
:Pin: [http://www.molex.com/molex/products/datasheet.jsp?part=active/0003091011_CRIMP_HOUSINGS.xml Molex 03-09-1011] [http://www.mouser.com/ProductDetail/Molex/03-09-1011/]
| Left turn signal power
| Green
|-
| Negative/Return
| Black
|-
| Right turn signal power
| Grey
|-
| Negative/Return
| Black
|}
;Note about Braking Regen
: Braking regen is activated by the pressure switch on the front brake lever or hydraulic switch on the rear brake pedal, through the rear brake power circuit.
: If that circuit doesn't complete (due to a failed bulb or wiring disconnect), braking regen seems to not activate.
;Routing
: Tail wiring runs through a sleeve by the [[#Controller|controller]] on the left side.
:: Ensure it is protected from chafing by the controller cover.
: Turn signal wires run through a pair of holes where the tail stalk meets the subassembly underneath the tail.
</onlyinclude>
[[Category:12V Component]]
[[Category:Wiring]]
