Difference between revisions of "Gen2/Drive Belt Adjustment"

From Unofficial Zero Manual
Jump to: navigation, search
(photos)
(link update)
 
(7 intermediate revisions by the same user not shown)
Line 1: Line 1:
The [[Official Owners Manual|official manual]] has a good procedure from which this is derived. Check that first.
+
<onlyinclude>
 
+
;Goal
Alignment of the belt is critically tough to get correct, and needs to be done everytime adjusting tension.
+
: Align and set belt tension to avoid bad wear and early breakage.
 +
: Alignment of the belt is critically tough to get correct, and needs to be done everytime adjusting tension.
 +
: Zero's [[Official Owners Manual]] has a good procedure from which this is derived. Check that first.
  
 
; Video instruction
 
; Video instruction
: [https://www.youtube.com/watch?v=mab3a7MWrpY How To Adjust Your Belt] on Youtube by Mistasam.
+
: [https://www.youtube.com/watch?v=mab3a7MWrpY Zero SR: How To Adjust Your Belt] on Youtube by NewZeroLand:
 +
:: {{#ev:youtube|mab3a7MWrpY}}
  
 
; Tools
 
; Tools
Line 12: Line 15:
 
: 13mm open-end wrench
 
: 13mm open-end wrench
 
; Instructions
 
; Instructions
# Place the motorcycle on a [[#Lift|lift or rear stand]] so the wheel spins freely.
+
# Place the motorcycle on a [[Lift]] or rear stand so the wheel spins freely.
 
# Loosen the rear axle nut on the right side (27mm) with the breaker bar.
 
# Loosen the rear axle nut on the right side (27mm) with the breaker bar.
 
#: [[File:Rear Axle Nut and right adjustment bolt.jpeg|200px|Rear Axle Nut and right adjustment bolt]] [[File:Rear Axle Spacer and left adjustment bolt.jpeg|200px|Rear Axle Spacer and left adjustment bolt]]
 
#: [[File:Rear Axle Nut and right adjustment bolt.jpeg|200px|Rear Axle Nut and right adjustment bolt]] [[File:Rear Axle Spacer and left adjustment bolt.jpeg|200px|Rear Axle Spacer and left adjustment bolt]]
 
# Loosen both left and right belt tension jam nuts (13mm) that face forward inside the adjusting gap.
 
# Loosen both left and right belt tension jam nuts (13mm) that face forward inside the adjusting gap.
 
#: [[File:Rear Axle Nut and right adjustment bolt - loosened.jpeg|200px|Rear Axle Nut and right adjustment bolt - loosened]] [[File:Rear Axle Spacer and left adjustment bolt - loosened.jpeg|200px|Rear Axle Spacer and left adjustment bolt - loosened]]
 
#: [[File:Rear Axle Nut and right adjustment bolt - loosened.jpeg|200px|Rear Axle Nut and right adjustment bolt - loosened]] [[File:Rear Axle Spacer and left adjustment bolt - loosened.jpeg|200px|Rear Axle Spacer and left adjustment bolt - loosened]]
# Turn both left and right adjustment nuts (13mm) one quarter turn at a time until belt tension reads in specification.
+
# Turn both left and right adjustment nuts (13mm) one quarter turn at a time to the desired [[Drive Belt/Tension Check|belt tension]].
 
#* Ensure that the alignment marks on either side of the swingarm indicate that the wheel and belt are aligned.
 
#* Ensure that the alignment marks on either side of the swingarm indicate that the wheel and belt are aligned.
 
#* Roll the wheel forward and track it flush with inside of rear sprocket.
 
#* Roll the wheel forward and track it flush with inside of rear sprocket.
Line 32: Line 35:
 
: [http://electricmotorcycleforum.com/boards/index.php?topic=6921 How to Adjust Your Zero's Belt]
 
: [http://electricmotorcycleforum.com/boards/index.php?topic=6921 How to Adjust Your Zero's Belt]
 
: [http://electricmotorcycleforum.com/boards/index.php?topic=6921.msg56601#msg56601 Notes via Shadow]
 
: [http://electricmotorcycleforum.com/boards/index.php?topic=6921.msg56601#msg56601 Notes via Shadow]
 +
</onlyinclude>
  
 
[[Category:Procedure]]
 
[[Category:Procedure]]
 +
[[Category:Maintenance]]

Latest revision as of 00:05, 30 March 2020

Goal
Align and set belt tension to avoid bad wear and early breakage.
Alignment of the belt is critically tough to get correct, and needs to be done everytime adjusting tension.
Zero's Official Owners Manual has a good procedure from which this is derived. Check that first.
Video instruction
Zero SR: How To Adjust Your Belt on Youtube by NewZeroLand:
Tools
27mm hex socket
Breaker bar
Torque wrench set to 75ft/lbs or 102Nm
13mm open-end wrench
Instructions
  1. Place the motorcycle on a Lift or rear stand so the wheel spins freely.
  2. Loosen the rear axle nut on the right side (27mm) with the breaker bar.
    Rear Axle Nut and right adjustment bolt Rear Axle Spacer and left adjustment bolt
  3. Loosen both left and right belt tension jam nuts (13mm) that face forward inside the adjusting gap.
    Rear Axle Nut and right adjustment bolt - loosened Rear Axle Spacer and left adjustment bolt - loosened
  4. Turn both left and right adjustment nuts (13mm) one quarter turn at a time to the desired belt tension.
    • Ensure that the alignment marks on either side of the swingarm indicate that the wheel and belt are aligned.
    • Roll the wheel forward and track it flush with inside of rear sprocket.
    • For proper alignment, the belt will track exactly centered on the wheel sprocket with a 1mm gap to either side of the belt relative to the sprocket.
      Once tension is set and tracking is flush to the inside, tightening the axle nut to 75ft-lbs will tend to nudge belt approximately 1mm to the outside.
    • Measure tension by rolling the wheel forward while plucking bottom side of belt or using tension gauge over several revolutions.
      Expect tension to vary slightly as wheel is rotated because front and rear sprockets are only round to a certain design tolerance.
  5. Check that the belt is aligned with belt tension in the right range.
  6. Re-tighten the left and right jam nuts (13mm).
  7. Tighten the axle nut (27mm) with the torque wrench (to 75ft-lbs).
References
Belt alignment discussion
How to Adjust Your Zero's Belt
Notes via Shadow