5,366
edits
Changes
cleanup with warning template
<onlyinclude>
This removes the helmet lock from the bike.
;Notes
: The following photos feature a ''2016-DSR'' bike.
;Tools
* 3mm Allen key
* ...
;Parts
;Instructions
# Remove the front fender
# Remove the cowl
# Loosen the bolt holding the ABS module in place from underneath, located above where the front fender was.
#: The ABS module appears to be mounted on two or three of these bolts with rubber vibration isolation around the bolts.
#: When this bottom bolt is free, the ABS module can be rotated from within the under-cowl area for better access to the innards.
#:[[File:MY2016DSR_helmetlock_absrotated.jpg|400px]]
# Drop the flasher relay and accessory power plugs out of the way and, using a mirror, locate the bolt holding the helmet lock in place.
#:[[File:MY2016DSR_helmetlock_mirrorview.jpg|400px]]
# Loosen the bolts holding the helmet lock in place.
#: The left one is more easily accessible.
#: Clearances for the right bolt are very tight and it may not be possible to rotate any tool to loosen the right bolt.
#: After removing the left bolt, it can be possible to loosen the right bolt by holding the right bolt in place and rotating the helmet lock itself.
#: {{Warning|The left side bolt will have a ground strap ring and bite washer attached, take extra care DO NOT lose these.}}
#:[[File:MY2016DSR_helmetlock_groundstrapbolt.jpg|thumb|none|Helmet lock ground strap bolt]][[File:MY2016DSR_helmetlock_mirrortool.jpg|thumb|none|Helmet lock mirror tool]]
#''Optional:'' [[Common Modifications#Chargetank Inlet Bracket|Chargetank Bracket Installation]]
#Reinstall the bottom bolt for the ABS unit bottom bolt, cowl, and front fender.
#'''Advanced:''' [[Advanced Modifications#Helmet Lock Relocation|Relocate the helmet lock]]
</onlyinclude>
[[Category:Procedure]]
[[Category:Modification]]
This removes the helmet lock from the bike.
;Notes
: The following photos feature a ''2016-DSR'' bike.
;Tools
* 3mm Allen key
* ...
;Parts
;Instructions
# Remove the front fender
# Remove the cowl
# Loosen the bolt holding the ABS module in place from underneath, located above where the front fender was.
#: The ABS module appears to be mounted on two or three of these bolts with rubber vibration isolation around the bolts.
#: When this bottom bolt is free, the ABS module can be rotated from within the under-cowl area for better access to the innards.
#:[[File:MY2016DSR_helmetlock_absrotated.jpg|400px]]
# Drop the flasher relay and accessory power plugs out of the way and, using a mirror, locate the bolt holding the helmet lock in place.
#:[[File:MY2016DSR_helmetlock_mirrorview.jpg|400px]]
# Loosen the bolts holding the helmet lock in place.
#: The left one is more easily accessible.
#: Clearances for the right bolt are very tight and it may not be possible to rotate any tool to loosen the right bolt.
#: After removing the left bolt, it can be possible to loosen the right bolt by holding the right bolt in place and rotating the helmet lock itself.
#: {{Warning|The left side bolt will have a ground strap ring and bite washer attached, take extra care DO NOT lose these.}}
#:[[File:MY2016DSR_helmetlock_groundstrapbolt.jpg|thumb|none|Helmet lock ground strap bolt]][[File:MY2016DSR_helmetlock_mirrortool.jpg|thumb|none|Helmet lock mirror tool]]
#''Optional:'' [[Common Modifications#Chargetank Inlet Bracket|Chargetank Bracket Installation]]
#Reinstall the bottom bolt for the ABS unit bottom bolt, cowl, and front fender.
#'''Advanced:''' [[Advanced Modifications#Helmet Lock Relocation|Relocate the helmet lock]]
</onlyinclude>
[[Category:Procedure]]
[[Category:Modification]]