5,366
edits
Changes
m
fix indentation
<onlyinclude>
For a number of errors, the [[Official Owners Manual|official manual]] recommends resetting the [[BMS]].
[[File:BMSwindows.jpg|thumb|BMS indicator lights and reset windows on a 2016 DSR]]
;Steps
# Key the bike off and unplug it from charging.
#: Wait for the contactor to click open.
# Uncover the battery LED indicators.
#: '''2015-2016:''' Remove the upper rubber pad from the front of the battery case.
#: '''2013-2014,2017+:''' Remove the rubber pad from the front of the battery case.
#: The uncovered hole reveals a string of small LEDs: one red on the left followed by four green.
#: They'll indicate charge level when the bike is keyed off.
# Uncover the diagnostic connection port and reset buttons.
#: '''2015-2016:''' Remove lower rubber pad from the front of the battery case.
#: '''2013-2014,2017+:''' These were uncovered in the previous step.
#: Notice a white plastic port coated in dielectric grease.
#: Above that port are two small micro-switch buttons which are the reset buttons.
#:* The ''left'' (as you face it) button performs a ''hardware'' reset.
#:* The ''right'' (as you face it) button performs a ''software'' reset.
# Press to reset
#: '''2013-2014:''' There is only one reset button above the plastic port which performs a ''hardware'' reset.
#: '''2015+:''' Take a pen (say) and depress the (right) ''software'' reset button for a few seconds and then release.
#: Expect the BMS indicating LEDs to go dark while the button is depressed and then turn on again when release.
#: The lights should stabilize after an initial startup sequence for a few seconds.
# Check whether the error code is clear by keying on the vehicle or whatever is appropriate.
# '''2015+:''' If the error is still present after a software reset, try the ''hardware'' reset button in the same way.
# '''2015+:''' If the error is still present after a hardware reset, try both at the same time.
# Replace the removed pads.
</onlyinclude>
[[Category:Procedure]]
[[Category:Diagnostics]]
For a number of errors, the [[Official Owners Manual|official manual]] recommends resetting the [[BMS]].
[[File:BMSwindows.jpg|thumb|BMS indicator lights and reset windows on a 2016 DSR]]
;Steps
# Key the bike off and unplug it from charging.
#: Wait for the contactor to click open.
# Uncover the battery LED indicators.
#: '''2015-2016:''' Remove the upper rubber pad from the front of the battery case.
#: '''2013-2014,2017+:''' Remove the rubber pad from the front of the battery case.
#: The uncovered hole reveals a string of small LEDs: one red on the left followed by four green.
#: They'll indicate charge level when the bike is keyed off.
# Uncover the diagnostic connection port and reset buttons.
#: '''2015-2016:''' Remove lower rubber pad from the front of the battery case.
#: '''2013-2014,2017+:''' These were uncovered in the previous step.
#: Notice a white plastic port coated in dielectric grease.
#: Above that port are two small micro-switch buttons which are the reset buttons.
#:* The ''left'' (as you face it) button performs a ''hardware'' reset.
#:* The ''right'' (as you face it) button performs a ''software'' reset.
# Press to reset
#: '''2013-2014:''' There is only one reset button above the plastic port which performs a ''hardware'' reset.
#: '''2015+:''' Take a pen (say) and depress the (right) ''software'' reset button for a few seconds and then release.
#: Expect the BMS indicating LEDs to go dark while the button is depressed and then turn on again when release.
#: The lights should stabilize after an initial startup sequence for a few seconds.
# Check whether the error code is clear by keying on the vehicle or whatever is appropriate.
# '''2015+:''' If the error is still present after a software reset, try the ''hardware'' reset button in the same way.
# '''2015+:''' If the error is still present after a hardware reset, try both at the same time.
# Replace the removed pads.
</onlyinclude>
[[Category:Procedure]]
[[Category:Diagnostics]]
