Gen2/Log Messages

This helps with the interpretation of log messages, for the MBB.

Message	Component	Interpretation
Riding	MBB	This is a data logging record, taken every 1 minute by default.
Charging	MBB	This is a charging logging record, taken every 10 minutes by default.
"Stats Read Failed, Resetting All Stats to Defaults"
ABS SILA reporting an error
BMS 1 Internal Disable Received	BMS
BMS Reset Unknown	BMS	The BMS Reset Procedure was performed.
BT RX buffer reset
Bad read pointer 0xFFFFFFFF is outside log bounds
Battery module contactor closed
Bike Shut Off After Idle For 3600 seconds.
CHECK SUCCESSFUL
CPU Soft
Calex 1200W Charger 1 Connected	Onboard Charger	SDS Platform only, but occurs on all Gen2 models.
Calex 1200W Charger 1 Disconnected	Onboard Charger	SDS Platform only, but occurs on all Gen2 models.
Calex 720W Charger 0 Connected	Onboard Charger	XMX Platform only, but occurs on all Gen2 models.
Calex 720W Charger 0 Disconnected	Onboard Charger	XMX Platform only, but occurs on all Gen2 models.
Disabling Calex 1200W Charger 1	Onboard Charger	SDS Platform only, but occurs on all Gen2 models.
Disabling Calex 720W Charger 0	Onboard Charger	XMX Platform only, but occurs on all Gen2 models.
Disabling External Chg 0 Charger 2
Disabling External Chg 1 Charger 3
Disarmed
Enabling Calex 1200W Charger 1	Onboard Charger	SDS Platform only, but occurs on all Gen2 models.
Enabling Calex 720W Charger 0	Onboard Charger	XMX Platform only, but occurs on all Gen2 models.
Enabling External Chg 0 Charger 2
Enabling External Chg 1 Charger 3
Entering Bootloader by request
Entering Charge Standby Mode
Entering Critical Error Shutdown
Event Log detected a bad
Event Log reformatted due to bad read pointer.
Event Log reformatted due to bad write pointer.
Event Log signature restored
Entered Test Mode
Exited Test Mode
Entering Hibernate
Exiting Hibernate
External Chg 0 Charger 2 Connected
External Chg 0 Charger 2 Disconnected
External Chg 1 Charger 3 Connected
External Chg 1 Charger 3 Disconnected
Key Off	Ignition	The bike was keyed off (intentionally or via electrical fault).
Key On	Ignition	The bike was keyed on (intentionally or via electrical fault).
Leaving Charge Standby Mode
Log data at offset 0x0:
Max allowed voltage difference is 500mV
Model year set to 2019 via CAN
Module CAN Link Down	BMS
Module CAN Link Up	BMS
Module Closing Contactor	BMS
Module Contactor is now Closed	BMS
Module Contactor is now Open	BMS
Module Opening Contactor	BMS
Module Registered	BMS
Module State Change Requires Disconnect	BMS
Module mode Change Does Not Require Disconnect	BMS
Module not connected	BMS
Module scheme changed from ??? mode to ??? mode	BMS	Modes None Charging Running Stopped
New Rev ?? is replacing Rev ??	MBB	Firmware update
Power Off Key Switch	Ignition	The bike was keyed off (intentionally or via electrical fault).
Power Off Onboard Charger	Onboard Charger	The bike was turned off by the onboard charger being unplugged or disengaged.
Power On Key Switch	Ignition	The bike was keyed on (intentionally or via electrical fault).
Power On Onboard Charger	Onboard Charger	The bike was turned on by the onboard charger being plugged in.
Powertank voltage too high and monolith ineligible for connection. Setting powertank as ineligible for connecton.	Power Tank
Precharge Decay Too Steep. Restarting Sevcon.	Sevcon motor controller
RN42 configuration complete
SEVCON CAN EMCY Frame Error	Motor Controller
Set Model to DS via CAN
Set VIN to 538S????????????? via CAN
Sevcon CAN Link Up	Motor Controller
Sevcon Contactor Drive OFF	Motor Controller
Sevcon Contactor Drive ON.	Motor Controller
Sevcon Entered Preop Mode	Motor Controller
Sevcon Turned Off	Motor Controller
Sevcon Turned On	Motor Controller